top of page
bgImage

Integrityhifi TRU-SWEEP Anti static Dust Brush

TRU-SWEEP Anti Static SPINNING Uni Pivot Dust Brush 

𝐓𝐑𝐔-𝐒𝐖𝐄𝐄𝐏 - Anti Static Uni Pivot Spinning Dust Brush

𝐐𝐮𝐚𝐥𝐢𝐭𝐲, 𝐀𝐞𝐬𝐭𝐡𝐞𝐭𝐢𝐜𝐬, 𝐀𝐬𝐬𝐮𝐫𝐚𝐧𝐜𝐞 & 𝐈𝐓 𝐖𝐎𝐑𝐊𝐒!

𝐍𝐨𝐭 𝐚𝐥𝐥 𝐩𝐫𝐨𝐝𝐮𝐜𝐭𝐬 𝐚𝐫𝐞 𝐜𝐫𝐞𝐚𝐭𝐞𝐝 𝐞𝐪𝐮𝐚𝐥. 

𝓦𝓱𝔂 & 𝓗𝓸𝔀?

Static is all around us and depending on weather conditions at times, it can be very bad. I’ve seen instances where a static discharge took out some expensive gear. There are a few precautions that can be taken to reduce the static in your surroundings but what we are going to focus on here is the stylus static as it happens in real time. This is what causes the annoying clicks and pops - these can only be removed using an anti static brush travelling at the same speed as the stylus. And for this we designed the Tru-Sweep Anti-static brush. It looks great and it works.

✅Crafted in solid (304 & 316 Surgical Stainless Steel). The perfectly balanced Uni-pivot arm allows the Camel Hair brush to gently track the grooves of the record.

With adjustable tracking force / skate force - you can control the speed of which the arm travels inward.

The soft Camel Hair brush gently sweeps across the record picking up fine dust and drains the static build up thru a connected ground wire keeping your stylus dust and static free.

✅How it works: Hair can conduct static electricity. The material that the Tru-Sweep is made from has continuity throughout the entire build of the unit. Once the static is encountered on the record, the electrons flow up the camel hair encounter the grounding conductor via wand portion where it travels to the uni-pivot bearing then transferred to the height extension of Tru-Sweep then to the base and discharged by the ground wire. This is connected to your Phono Pre-amp ground lug or to your receiver ground lug or amplifier ground lug

MSRP $295 USD

TRU-SWEEP Anti Static Dust Brush

3 SIZES AVAILABLE:

SMALL, MEDIUM & LARGE

All have SOLID round bases & Solid Rod.

Small - 1" TO 1 3/4"

Medium 1 3/8" TO 2 1/8"

Large 1 3/4" TO 2 1/2"

Measure from top of the plinth to the top of the platter to get the size you need.

For Custom heights, contact us.

Special long arm available for VPI AVENGER,

Inquire through our dealers

Each unit is adjustable in height by 3/8". Round large base and the riser is constructed of 304 S.S. same as the lifter.

The 1/4" arm rod and the removable brush head is 316 Surgical S.S, this is important as it contains the greatest proprieties in the S.S. Family which makes it most suitable for our purpose which is to drain static as it happens in real time.

Sliding along the arm is a collet that we use as fine tracking/skate force. 

In the rear of the arm is the counter weight adjustable with a set screw. 

The brush of course is fine soft Camel hair also removable for easy washing.

The drain ground wire is attached to the large base.

Removable head brush for easy warm water washing.

Allen Key included for adjusting height & removing head as all have set screws.

Blu tac included for the base.

Ground Wire is also included. - COLOR MAY VARY

COMES FULLY ASSEMBLED IN 3 PARTS - ROD & THE BASE

TRU-SWEEP Anti Static Dust Brush

100% Made in Canada

SPECIAL CUSTOM HEIGHTS

Now with upgraded 12 Gauge braided BLACK copper wires

LIMITLESS HEIGHT can be reached by adding solid stackable stainless steel pucks.

X LARGE $359 - 2 1/8" TO 2 7/8"

XX TRA LARGE $425 - 2 1/2" TO 3 1/4"

SETTING UP TRU-SWEEP Anti Static Dust Brush

Contact us if you need any help - trulift@yahoo.ca

TRU-SWEEP ANTI STATIC DUST BRUSH

HEIGHT ADJUSTMENT & ADJUSTING SKATE /TRACKING FORCE

Blu Tac is included for Placement Stability. 3 tiny dots (less than pictured will assure balance & stability)

TRU-SWEEP Anti Static Dust Brush IN ACTION...

For any CUSTOM SIZED Tru-Sweep Anti Static Dust Brush,

Please contact us, we can help. TRULIFT@YAHOO.CA

It can be ordered through our dealers.

bottom of page